Máy hiện sóng Hantek DSO5202P 2 kênh dải đo 200Mhz - Digital Oscilloscope DSO5202P 200MHZ

Tên Sản phẩm:  Máy hiện sóng Hantek DSO5202P
Giá: Liên hệ:  KD1: 0984.935.296 - KD2: 076.343.4444 Để lấy báo giá từng loại


Mô tả:

 Máy hiện sóng Hantek DSO5202P 2 kênh dải đo 0-200Mhz Bảo hành 12 tháng. Miễn phí vận chuyển toàn quốc 1. Feature 200MHz bandwidths 1GSa/s Real Time sample rate Large (7.0-inch) color display,WVGA(800x480) Record length up to 40K Trigger mode: edge/pulse width/line select...

Máy hiện sóng Hantek DSO5202P 2 kênh dải đo 0-200Mhz

Bảo hành 12 tháng.  Miễn phí vận chuyển toàn quốc

1. Feature

• 200MHz bandwidths
• 1GSa/s Real Time sample rate
• Large (7.0-inch) color display,WVGA(800x480)
• Record length up to 40K
• Trigger mode: edge/pulse width/line selectable video/slop/overtime etc.
• USB host and device connectivity, standard
• Multiple automatic measurements
• Four math functions, including FFTs standard
• Provides software for PC real-time analysis
• VGA Optional

• 2. Specifications

  Model	DSO5202P
  Acquisition
  Sample Rate	Real-Time Sample: 1GS/s
  Acquisition Modes
  Normal	Normal data only
  Peak Detect	High-frequency and randon glith capture
  Average	Wavefom Average, selectable 4,8,16,32,64,128
  Inputs
  Inputs Coupling	AC, DC, GND
  Inputs Impendance	1MΩ±2% ‖20pF±3pF
  Probe Attenuation	1X, 10X
  Supported Probe Attenuation Factor	1X, 10X, 100X, 1000X
  Maximum Input Voltage	CAT I and CAT II: 300VRMS (10×), Installation Category; CAT III: 150VRMS (1×); Installation Category II: derate at 20dB/decade above 100kHz to 13V peak AC at 3MHz* and above. For non-sinusoidal waveforms, peak value must be less than 450V. Excursion above 300V should be of less than 100ms duration. RMS signal level including all DC components removed through AC coupling must be limited to 300V. If these values are exceeded, damage to the oscilloscope may occur.
  Horizontal System
  Sample Rate Range	500MS/s--1GS/s
  Waveform Interpolation	(sin x)/x
  Record Length	40K
  SEC/DIV Range	2ns/div to 40s/div
  Sample Rate and Delay Time Accuracy	±50ppm(at over any ≥1ms time interval)
  Position Range	2ns/div to 10ns/div;  (-4div x s/div) to 20ms;
  Delta Time Measurement Accuracy  (Full Bandwidth)	Single-shot, Normal mode:± (1 sample interval +100ppm × reading + 0.6ns); >16 averages:± (1 sample interval + 100ppm × reading + 0.4ns); Sample interval = s/div ÷ 200
  Vertical System
  Vertical Resolution	8-bit resolution, all channel sampled simultaneously
  Position Range	2mV/div to 10V/div
  Bandwidth	200MHz
  Rise Time at BNC( typical)	1.8ns
  Analog Bandwidth in Normal and Average modes at BNC or with probe, DC Coupled	2mV/div to 20mV/div, ±400mV;  50mV/div to 200mV/div, ±2V 500mV/div to 2V/div, ±40V; 5V/div, ±50V
  Math	+, -, *, /, FFT
  FFT	Windows: Hanning, Flatop, Rectamgular, Bartlett, Blackman; 1024 sample point
  Bandwidth Limit	20MHz
  Low Frequency Response (-3db)	≤10Hz at BNC
  DC Gain Accuracy	±3% for Normal or Average acquisition mode, 5V/div to 10mV/div; ±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div
  DC Measurement Accuracy,  Average Acquisition Mode	When vertical displacement is zero, and N ≥16:± (3% × reading + 0.1div + 1mV) only 10mV/div or greater is selected;  When vertical displacement is not zero, and N≥16: ± [3% × (reading + vertical position) + 1% of vertical position + 0.2div]; Add 2mV for settings from 2mV/div to 200mV/div; add 50mV for settings from 200mV/div to 5V/div
  Volts Measurement Repeatability,  Average Acquisition Mode	Delta volts between any two averages of ≥16 waveforms acquired under same setup and ambient conditions
  Trigger System
  Trigger Types	Edge, Video, Pulse, Slope, Over time, Alternative
  Trigger Source	CH1, CH2, EXT, EXT/5, AC Line
  Trigger Modes	Auto, Normal, Single
  Coupling Type	DC, AC, Noise Reject, HF Reject, LF Reject
  Trigger Sensitivity (Edge Trigger Type)	DC(CH1,CH2): 1div from DC to 10MHz; 1.5div from 10MHz to 100MHz; 2div from 100MHz to Full; DC(EXT):  200mV from DC to 100MHz; 350mV from 100MHz to 200MHz; DC(EXT/5):        1V from DC to 100MHz;1.75V from 100MHz to 200MHz;        AC: Attenuates signals below 10Hz; HF Reject: Attenuates signals above 80kHz  LF Reject: Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 150kHz
  Trigger Level Range	CH1/CH2: ±8 divisions from center of screen;  EXT: ±1.2V; EXT/5:±6V
  Trigger Level Accuracy( typical)Accuracy is for signals having rise and fall times ≥20ns	CH1/CH2: 0.2div × volts/div within ±4 divisions from center of screen; EXT: ± (6% of setting + 40mV); EXT/5: ± (6% of setting + 200mV);
  Set Level to 50%(typical)	Operates with input signals ≥50Hz
  Video Trigger
  Video Trigger Type	CH1, CH2: Peak-to-peak amplitude of 2 divisions; EXT: 400mV; EXT/5: 2V
  Signal Formats and Field Rates, Video Trigger Type	Supports NTSC, PAL and SECAM broadcast systems for any field or any line
  Holdoff Range	100ns ~ 10s
  Pulse Width Trigger
  Pulse Width Trigger Mode	Trigger when (< , >, = , or ≠); Positive pulse or Negative pulse
  Pulse Width Trigger Point	Equal: The oscilloscope triggers when the trailing edge of the pulse crosses the trigger level. Not Equal: If the pulse is narrower than the specified width, the trigger point is the trailing edge. Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width. Less than: The trigger point is the trailing edge. Greater than (also called overtime trigger): The oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width
  Pulse Width Range	20ns ~ 10s
  Slope Trigger
  Slope Trigger Mode	Trigger when (< , > , = , or ≠ ); Positive slope or Negative slope
  Slope Trigger Point	Equal: The oscilloscope triggers when the waveform slope is equal to the set slope. Not Equal: The oscilloscope triggers when the waveform slope is not equal to the set slope. Less than: The oscilloscope triggers when the waveform slope is less than the set slope. Greater than: The oscilloscope triggers when the waveform slope is greater than the set slope.
  Time Range	20ns ~ 10s
  Overtime Trigger
  Over Time Mode	Rising edge or Falling edge
  Time Range	20ns ~ 10s
  Alternative Trigger
  Trigger on CH1	Internal Trigger: Edge, Pulse Width, Video, Slope
  Trigger on CH2	Internal Trigger: Edge, Pulse Width, Video, Slope
  Trigger Frequency Counter
  Readout Resolution	6 digits
  Accuracy (typical)	±30ppm (including all frequency reference errors and ±1 count errors)
  Frequency Range	AC coupled, from 4Hz minimum to rated bandwidth
  Signal Source	Pulse Width or Edge Trigger modes: all available trigger sources The Frequency Counter measures trigger source at all times, including when the oscilloscope acquisition pauses due to changes in the run status, or acquisition of a single shot event has completed. Pulse Width Trigger mode: The oscilloscope counts pulses of significant magnitude inside the 1s measurement window that qualify as triggerable events, such as narrow pulses in a PWM pulse train if set to < mode and the width is set to a relatively small time. Edge Trigger mode: The oscilloscope counts all edges of sufficient magnitude and correct polarity. Video Trigger mode: The Frequency Counter does not work.
  Measure
  Cursor Measurement	Voltage difference between cursors: △V Time difference between cursors: △T Reciprocal of △T in Hertz (1/ΔT)
  Auto Measuerment	Frequency, Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time, Fall Time, +Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid, Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS, FOVShoot, RPREShoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF
  Display
  Display Type	7 inch 64K color TFT (diagonal liquid crystal)
  Display Resolution	800 horizontal by 480 vertical pixels
  Display Contrast	Adjustable (16 gears) with the progress bar
  Probe Compensator Output
  Output Voltage( typical)	About 5Vpp into ≥1MΩ load
  Frequency(typical)	1kHz
  Power Supply
  Supply Voltage	100-120VACRMS(±10%), 45Hz to 440Hz, CATⅡ 120-240VACRMS(±10%), 45Hz to 66Hz, CATⅡ
  Power Consumption	<30W
  Fuse	2A, T rating, 250V
  Environmental
  Temperature	Operating: 32℉to 122℉(0℃to 50℃); Nonoperating: -40℉to 159.8℉(-40℃to +71℃)
  Cooling Method	Convection
  Humidity	+104℉or below (+40℃or below): ≤90% relative humidity; 106℉to 122℉(+41℃to 50℃): ≤60% relative humidity
  Altitude	Operating: Below 3,000m (10,000 feet); Nonoperaring: Below 15,000m(50,000 feet)
  Mechanical
  Size	Length 385mm, Width 200mm, Height 245mm
  Weight	3.5KG(with Packing);  2.08KG(without Packing）

   

  3. Other Pictures

4. Standard Accessory:

ĐỊNH NGHĨA SẢN PHẨM

- Sản phẩm chính hãng: Là những sản phẩm được đính kèm nhóm từ "chính hãng...", đây là những sản phẩm chính hãng như TI, ST, NS, HANTEK, UNI-T,... Chúng tôi khuyến khích khách hàng mua các sản phẩm này.  Chất lượng sản phẩm tốt và không gặp phải rủi ro khi sử dụng.